Bug-o-systems Speed Weaver II Manual de usuario descargar pdf (Pagina 11)

WIRING DIAGRAMWIRE LIST

ITEM DESCRIPTION

W/BLK Switched line power, weave board to tractor outlet

W/BRN Speed signal voltage, weave to speed board, 0-8 V

W/RD Weld contact switch control to weave board, 8 or -5 V

W/OR Made select switch to weave board

W/GRN Stop on dwell, weave board to selector switch

W/BLU Fwd/Rev signal, 0 or 8 V, weave board to speed board

W/GY Step, 0 or 8 V, weave board to selector switch

W/B/OR Delay left, pot to weave board

W/B/GRN-1 Weld contact, weave board to amphenol

W/B/GRN-2 Weld contact, weave board to amphenol

W/B/BLU Delay right, pot to weave board

BLK-1 Input line to power switch, hot side

BLK-2 Power line, switch to circuit-breaker

BLK-3 Power line to weave board, for tractor switch

BLK-4 Power line from circuit-breaker to transformer

BRN Speed signal fr om speed pot to weave board, 0-8 V

RED Motor current

OR-1 Weld switch to selector switch, 8 V line

OR-2 Selector switch to dwell pot-right

OR-3 Dwell pot-right to dwell pot-left

OR-4 Dwell pot-left to speed pot

OR-5 Speed pot to 8 V supply from weave board

YEL-1 -5 V from speed board to weld switch

YEL-2 Weld contact switch to mode select switch, -5 V

YEL-3 Select switch to sensor connector, -5 V

YEL-4 Select switch to sensor connector, -5 V

GRN-1 Power line ground, line cord to machine case

GRN-2 Ground, case to tractor power socket

LT.BLU Circuit common (O V), speed board to speed pot

BLU-1 Common (O V), selector switch to motor

BLU-2 Common, speed board to selector switch

BLU-3 Common, transformer C.T. to speed board

BLU-4 Transformer C.T. to weave board, O-V ref.

VIO Sensor input, left, sensor to weave board

GY-1 Sensor input, right

WHT-1 Power input line

WHT-2 Line power, on-off switch to outlet

WHT-3 Line power, outlet to 20 V.C.T. transformer

TN-1 Transformer sec., supply to speed board

TN-2 Transformer sec., supply to weave board

TN-3 Transformer sec., supply to speed board

TN-4 Transformer sec., supply to weave board

PINK Motor current, speed board to selector switch

6. Mode Selector Switch.

The 5-position Switch (J) is used to select any one of four welding

modes, described below, or to eject the cross rail.

A. RUN: In this mode, power to the tractor is always on, and the

tractor travels continuously both during weave and dwell.

Weave speed and dwell time both affect the weld patterns.

B. STEP: The tractor travels only during dwell, and stops during

the oscillator cross stroke. Changing weave speed does not

affect the weld pattern, dwell time does.

C. TRACTOR STOP ON DWELL: This is a new mode that has

proven very advantageous in certain cases. The tractor and

oscillator travel simultaneously during the weave stroke, both

stop during dwell. Dwell time thus does not affect the weld

pattern, it controls the weld deposit on each side.

D. NO WEAVE: In this mode oscillation is stopped and only the

tractor moves, to make stringer passes.

E. Switchingtothefthpositionwillejecttherail.

WELD PATTERNS:

When mounted on a tractor plugged into its panel, the Weaver

produces the above weld patterns; shown for increasing dwell time or

tractor speed from left to right.

1 2 ... 6 7 8 9 10 11 12 13 14

Comentarios a estos manuales

Sin comentarios

Bug-o-systems Speed Weaver II Manual de usuario Pagina 11

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Bug-o-systems Speed Weaver II